Plastic Accessories
FCS-706
Threaded Plastic
Setting Plugs
Setting Plugs
FCS-706 Threaded plastic setting
plugs are used to set NC threaded inserts. Can be nailed directly to formwork
to set inserts.
FCS-700
Plastic Dowel Caps
FCS-700 Plastic dowel caps
are used to allow smooth dowels to move in a contraction joint. Dowel caps are
manufactured with a positive stop in the cap. Dowel caps are available in 1/2”,
5/8”, 3/4”, 7/8”, 1”, 1-1/4”, and 1-1/2” diameters.
All dowel caps are 4” long.
Products
FCS-701
Plastic Rebar Safety Cap
FCS-701 Plastic rebar safety
cap “mushroom cap” is used to protect workers from projecting rebar
on job sites. Available in #4 and #11 sizes.
FCS-707 Plastic
Plugs
FCS-707
Plastic plugs are used to plug snap ties holes in plywood forms. Available
in 9/16” (5,000 pcs/bag) and 13/16” (2,500 pcs/bag) diameters.
FCS-708 45°
Plastic Tie Wire Reels
FCS-708
Plastic rebar tie wire reels are attached to iron workers’ belts to dispense
tie wire. Plain or epoxy coated. Can be loaded in reels.
FCS-702
OSHA Approved Safety Cap (PC-100)
FCS-702 The “PC-100”
safety cap is certified by CAL-OSHA to protect construction workers from impalement
injuries by falls up to 7-1/2 ft. The U.S. Dept. of Labor has reviewed product
data associated with the PC-100 and concluded that the device meets applicable
federal OSHA requirements relating to impalement injuries.
FCS-709 Plastic
Coil Tie Cones
FCS-709
Plastic coil tie cones are used to screw on coil ties to create break backs. For
use with 1/2”, 3/4”, 1”, and 1-1/4” coil ties. Set back of
1” for 1/2” and 3/4” coil ties; 2” for 1” and 1-1/4”
coil ties.
FCS-703
All-Plastic Beam Bolsters
FCS-703 All-plastic beam bolster
is designed to support extreme weight loads for lower slab steel from slab forms.
Corrugations spaced at 1” centers serve as guides for spacing rebar. Legs
are solid polyethylene on 2-1/2” centers. Plastic arch design maximizes strength
between legs. Supporting crossbar is made from high-strength plastic-coated steel.
Corrosion-free and lightweight for handling.
FCS-710 Push-Fit
Cones
FCS-710
Push-fit cones are used with class 200 x 3/4” PVC pipe to create a sleeve
for 3/4” inner rods. Cones and inner rods are reusable.
FCS-704
All-Plastic High Chairs
FCS-704 All-plastic high chairs
are used in slabs where no exposed or non stainless steel metal is allowed. Excellent
for supporting epoxy-coated rebar in bridge deck construction or wherever a corrosion-free
support is required. The chair is made of high-impact polypropylene, and its design
gives it the strength of steel.
FCS-711 Grout
Retention Rings
FCS-711
Grout retention rings are used on smooth dowels to prevent grout from leaking
out of drilled holes. Available in 1”, 1-1/4”, and 1-1/2” diameters.
FCS-705
PVC Shims
FCS-705 PVC shims are made
out of high-impact plastic. Available in 1/16”, 1/8”, and 1/4”
thickness and 4” x 6” squares. Corrugated to ensure a no-slip surface.
